Search Results

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

Search Again
Page 8 of 10
  1. Rapid LED
    Post

    Rapid DIY led questions

    At the very end of checkout there's a space for "special instructions", you can just list your preferences there. If we get an order w/o any...
    Post by: Rapid LED, May 2, 2011 in forum: RapidLED
  2. Rapid LED
    Post

    Rapid DIY led questions

    As exactly mentioned the ultra kits come with XP- series LEDs. Those will output about 20-30% more light than the XR-E's, though the lens selection...
    Post by: Rapid LED, May 1, 2011 in forum: RapidLED
  3. Rapid LED
    Post

    led problem/question

    Hello, Unfortunately that is very common with the Meanwell ELN drivers. Sometimes the LEDs will be barely lit, while other times (using the same...
    Post by: Rapid LED, Apr 25, 2011 in forum: RapidLED
  4. Rapid LED
    Post

    New led setup

    That page won't load for me, but based on the specs you listed you would need to get two additional LPC-60-1050 drivers for 4 of these LEDs (the...
    Post by: Rapid LED, Apr 24, 2011 in forum: RapidLED
  5. Rapid LED
    Post

    New led setup

    I'd need to see the specs of the LEDs to be able to say for sure, but my guess is they'd need to be run on separate drivers.
    Post by: Rapid LED, Apr 22, 2011 in forum: RapidLED
  6. Rapid LED
    Post

    LED Recommendation

    The LED + lens is roughly 0.5-0.6". For fans typically we install them so they are blowing down on the heatsink, if you can't do that then...
    Post by: Rapid LED, Apr 18, 2011 in forum: RapidLED
  7. Rapid LED
    Post

    new led lights

    No, on top of the kits you'll need a heatsink(s) and fan(s), as well as a method to control dimming. If you don't have a controller (ie. Apex, Reef...
    Post by: Rapid LED, Apr 10, 2011 in forum: RapidLED
  8. Rapid LED
    Post

    new led lights

    60 LEDs is about right for that sized tank. It's often easiest to go with our kits, so perhaps a 48 kit and a 12 kit. Your choices after that would...
    Post by: Rapid LED, Apr 8, 2011 in forum: RapidLED
  9. Rapid LED
    Post

    LED Recommendation

    At that height I think 5" to cover 18" is fine.
    Post by: Rapid LED, Apr 1, 2011 in forum: RapidLED
  10. Rapid LED
    Post

    LED Recommendation

    Okay a single brace makes more sense, that would be two heatsinks per section which sounds about right, however you're going to get some light...
    Post by: Rapid LED, Mar 31, 2011 in forum: RapidLED
  11. Rapid LED
    Post

    LED Recommendation

    I think that's more than enough light for your tank, though you do have a lot of light in there already so the tank is probably used to a good amount...
    Post by: Rapid LED, Mar 30, 2011 in forum: RapidLED
  12. Rapid LED
    Post

    led spacing

    If you can get a 6" x 9" space then 12 LEDs would be fine, otherwise you're probably only going to be able to cram 6-8 LEDs in there (from what I...
    Post by: Rapid LED, Mar 11, 2011 in forum: LED Aquarium Lighting
  13. Rapid LED
    Post

    New PWM controller on sale now!

    You have limited control of what you can do to each color/channel with this controller. For example, if you're in manual mode you can adjust the...
    Post by: Rapid LED, Mar 5, 2011 in forum: RapidLED
  14. Rapid LED
    Thread

    New PWM controller on sale now!

    Hello 3Reefers, Just wanted to let everybody know that we have a brand new PWM controller out on the site today. This will give you your choice of...
    Thread by: Rapid LED, Mar 3, 2011, 4 replies, in forum: RapidLED
  15. Rapid LED
    Post

    kit recommendation

    If you're keeping SPS in that tank you'll want about 18-20 LEDs. We don't have a kit like that but we can put one together if you'd like. Just let...
    Post by: Rapid LED, Feb 25, 2011 in forum: RapidLED
  16. Rapid LED
    Post

    Kit recommendation

    Hi Chris, for that sized tank I'd go with somewhere between 90-110 LEDs, depending on which ones you get. Since you have the Apex controller it's...
    Post by: Rapid LED, Feb 11, 2011 in forum: RapidLED
  17. Rapid LED
    Post

    Led spread without optics

    I think 12 LEDs will be enough to add some nice blue to the tank.
    Post by: Rapid LED, Feb 6, 2011 in forum: RapidLED
  18. Rapid LED
    Post

    Led spread without optics

    How many T5's are you trying to replace? (and what watt)
    Post by: Rapid LED, Feb 5, 2011 in forum: RapidLED
  19. Rapid LED
    Post

    Sale on Actinic Kits only for 3Reef Members!

    If you're mixing your colors then yes, that's enough for SPS as well. If you're just using blue as supplements then that would depend on what your...
    Post by: Rapid LED, Feb 2, 2011 in forum: RapidLED
  20. Rapid LED
    Post

    Sale on Actinic Kits only for 3Reef Members!

    Each LED is 3W, but wattage is misleading as the actual running wattage depends on the current that the LED is being run at. If you're using a 700mA...
    Post by: Rapid LED, Feb 2, 2011 in forum: RapidLED
Showing results 141 to 160 of 189 Next >
Search Again
Page 8 of 10