Search Results

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

Search Again
Page 1 of 10
  1. AZDesertRat
    Post

    want to start a phosban reactor for a nanocube

    At that price point they should sell like crazy! Might have to try one myself on my 16G nano.
    Post by: AZDesertRat, Oct 6, 2011 in forum: Filters, Pumps, etc..
  2. AZDesertRat
    Post

    want to start a phosban reactor for a nanocube

    There are problems with mixing the media though. For one, GFO and carbon have very different useful lives so you are either wasting GFO or extending...
    Post by: AZDesertRat, Oct 6, 2011 in forum: Filters, Pumps, etc..
  3. AZDesertRat
    Post

    Running out of solutions for microbubble problem

    Lower the Koralia further in the tank. I found with some of my powerheads they were vortexing and creating bubbles. It was easier to see at night...
    Post by: AZDesertRat, Oct 6, 2011 in forum: General Reef Topics
  4. AZDesertRat
    Post

    RO/DI Unit

    Its not even worth the $65 and wil cost you a fortune to operate. It used low quality high micron, non standard replacement filters that are hard to...
    Post by: AZDesertRat, Oct 6, 2011 in forum: Filters, Pumps, etc..
  5. AZDesertRat
    Post

    Venting/Any advice?

    And here are some bulkhead installation tips: http://www.3reef.com/forums/new-hobby/bulkhead-installation-tips-111422.html
    Post by: AZDesertRat, Oct 6, 2011 in forum: ASAP
  6. AZDesertRat
    Post

    Glass cleaning inside old tank

    A razor scraper if its glass and a plastic edged scraper or an old credit card if its acrylic.
    Post by: AZDesertRat, Oct 6, 2011 in forum: New To The Hobby
  7. AZDesertRat
    Post

    want to start a phosban reactor for a nanocube

    It only takes one level tablespoonfull of GFO or about 10 grams per 10 gallons of system water full dose so a reactor would be overkill for 2.5...
    Post by: AZDesertRat, Oct 5, 2011 in forum: Filters, Pumps, etc..
  8. AZDesertRat
    Post

    Best powerheads for ReefKeeper Lite?

    The Koralia Evolutions are designed to be used with a controller, the old K series are not. If the 750 is a Evo, contact Hydor customer service for...
    Post by: AZDesertRat, Oct 5, 2011 in forum: Filters, Pumps, etc..
  9. AZDesertRat
    Post

    New RO Membrane Releasing 111 PPM!

    The filter flush is done with the line between the cabon block and the RO membrane disconnected so you don't get any preservatives, carbon dust or...
    Post by: AZDesertRat, Oct 5, 2011 in forum: Filters, Pumps, etc..
  10. AZDesertRat
    Post

    Glass cleaning inside old tank

    I use straight undiluted distilled white vinegar. Lay the tank on its side or back, soak a towel or rag in vinegar and let it sit on the spot for...
    Post by: AZDesertRat, Oct 5, 2011 in forum: New To The Hobby
  11. AZDesertRat
    Post

    New RO Membrane Releasing 111 PPM!

    I believe you said you had a flush kit, its not open is it? All the water should be going through the flow restrictor not bypassing it. The filters...
    Post by: AZDesertRat, Oct 5, 2011 in forum: Filters, Pumps, etc..
  12. AZDesertRat
    Post

    New RO Membrane Releasing 111 PPM!

    To flush the filters individually, you remove all filters and install just the first sediment filter and screw the other housings back on empty....
    Post by: AZDesertRat, Oct 4, 2011 in forum: Filters, Pumps, etc..
  13. AZDesertRat
    Post

    Moving sump to basement

    I built the small stand right of my reef to house a chiller and equipment. When I went to LEDs the chiller was no longer needed so it can no house...
    Post by: AZDesertRat, Oct 3, 2011 in forum: I made this!
  14. AZDesertRat
    Post

    Moving sump to basement

    Wow, look at the wattage required to pump that high though. Thats 24/7/365 so adds up over time. Personally I have gone the opposite direction and...
    Post by: AZDesertRat, Oct 3, 2011 in forum: I made this!
  15. AZDesertRat
    Post

    New RO Membrane Releasing 111 PPM!

    Flush kits are a waste of money and really do nothing other than lighten your wallet and give you a warm fuzzy feeling. Notice most long time RO/DI...
    Post by: AZDesertRat, Oct 1, 2011 in forum: Filters, Pumps, etc..
  16. AZDesertRat
    Post

    Coralife RO ID

    Coralife uses a standard 1812 configuration so any Dow Filmtec or Spectrapure membrane will fit in your housing. Make sure you get the correct sized...
    Post by: AZDesertRat, Oct 1, 2011 in forum: Filters, Pumps, etc..
  17. AZDesertRat
    Post

    Bayferrox® C or G grade as GFO (granular feric oxide)

    Not sure who the question was directed to but the pelletized media is found here: Bulk Pellet GFO (Phosphate Remover) - English I am in the water...
    Post by: AZDesertRat, Oct 1, 2011 in forum: General Reef Topics
  18. AZDesertRat
    Post

    Coralife RO ID

    You will have to remove the membrane from the housing to see what you have. It will be printed or stamped on the membrane. If you are planning to...
    Post by: AZDesertRat, Oct 1, 2011 in forum: Filters, Pumps, etc..
  19. AZDesertRat
    Post

    New RO Membrane Releasing 111 PPM!

    Did you disconnect the DI and flush the first 3 to 5 gallons of RO to waste before using any of it? Its possible the membrane is not seated all...
    Post by: AZDesertRat, Oct 1, 2011 in forum: Filters, Pumps, etc..
  20. AZDesertRat
    Post

    Bayferrox® C or G grade as GFO (granular feric oxide)

    There may be other differences but it may not matter with a reef tank. For one, the Bayoxide products carry ANSI/NSF and EPA approvals for use in...
    Post by: AZDesertRat, Oct 1, 2011 in forum: General Reef Topics
Showing results 1 to 20 of 199 Next >
Search Again
Page 1 of 10