Search Results

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

Search Again
Page 5 of 10
  1. wiigelec
    Post

    need help with bowfront cabinet design

    Resaw or purchase 1/4" thickness wood of your choice. Build a particle board form that has the radius of bend you wish to achieve. Glue laminate...
    Post by: wiigelec, Feb 15, 2011 in forum: General Reef Topics
  2. wiigelec
    Post

    need help with bowfront cabinet design

    Two other options are to bandsaw the curves if your stock is thick enough, or laminate thin strips over a bending form...
    Post by: wiigelec, Feb 15, 2011 in forum: General Reef Topics
  3. wiigelec
    Post

    Show me your DIY wall mounts for pendants

    Used to translate a marking vertically... Plumb-bob - Wikipedia, the free encyclopedia
    Post by: wiigelec, Feb 13, 2011 in forum: I made this!
  4. wiigelec
    Post

    Show me your DIY wall mounts for pendants

    Use a plumb-bob and mark each corner of the tank on your ceiling then center from there... Yes. Personally and depending on the weight of the...
    Post by: wiigelec, Feb 13, 2011 in forum: I made this!
  5. wiigelec
    Post

    Nova T5 acting weird...

    Before I went nuts changing out ballasts I would first eliminate the possibilities that are easier to fix... ...like the timers. Sometimes the...
    Post by: wiigelec, Feb 13, 2011 in forum: T5 Aquarium Lighting
  6. wiigelec
    Post

    Show me your DIY wall mounts for pendants

    Depending on where your ceiling joists are located and which way they run this may work for you or it may not, and hopefully I can paint a picture...
    Post by: wiigelec, Feb 12, 2011 in forum: I made this!
  7. wiigelec
    Post

    Nova T5 acting weird...

    What is it plugged into?
    Post by: wiigelec, Feb 12, 2011 in forum: T5 Aquarium Lighting
  8. wiigelec
    Post

    Help with switch replacement

    I bet you miss it;D I left for a while but found my way back...
    Post by: wiigelec, Feb 10, 2011 in forum: Reef Lighting
  9. wiigelec
    Post

    Help with switch replacement

    A higher amp rated switch would be suitable...
    Post by: wiigelec, Feb 10, 2011 in forum: Reef Lighting
  10. wiigelec
    Post

    HOB filter overflow

    ....then the filter pump runs dry and burns up...
    Post by: wiigelec, Feb 9, 2011 in forum: Filters, Pumps, etc..
  11. wiigelec
    Post

    HOB filter overflow

    An overflow works by draining the water out of tank that is pumped into the tank by the return pump ie ReturnIn = OverflowOut. You will find...
    Post by: wiigelec, Feb 9, 2011 in forum: Filters, Pumps, etc..
  12. wiigelec
    Post

    ground probe

    Plagiarism is a strong accusation that should not be made without substantiation...
    Post by: wiigelec, Feb 3, 2011 in forum: New To The Hobby
  13. wiigelec
    Post

    pictures of GFCI fire

    Something is not right, a properly functioning GFCI should not allow that much damage to occur. Have you had this looked at?
    Post by: wiigelec, Feb 3, 2011 in forum: General Reef Topics
  14. wiigelec
    Post

    pictures of GFCI fire

    I don't think that thing had GFCI protection: Shop Over-Load Guard 8-Outlet Dual Circuit Breaker Power Center at Lowes.com
    Post by: wiigelec, Feb 3, 2011 in forum: General Reef Topics
  15. wiigelec
    Post

    GFCI, do you recommend one? Discuss...

    http://www.3reef.com/forums/general-reef-topics/use-driploop-82336.html http://www.3reef.com/forums/general-reef-topics/pictures-gfci-fire-96962.html
    Post by: wiigelec, Feb 3, 2011 in forum: General Reef Topics
  16. wiigelec
    Post

    GFCI, do you recommend one? Discuss...

    When conductive saltwater drips into your power strip and causes an arcing ground fault that is insufficient in magnitude to trip the instantaneous...
    Post by: wiigelec, Feb 3, 2011 in forum: General Reef Topics
  17. wiigelec
    Post

    GFCI, do you recommend one? Discuss...

    http://www.3reef.com/forums/general-reef-topics/please-use-gfci-82339.html
    Post by: wiigelec, Feb 3, 2011 in forum: General Reef Topics
  18. wiigelec
    Post

    ground probe

    Very well than: http://www.hubbell-wiring.com/press/PDFS/H5212.pdf Trip Level - 4 - 6 mA Same as the Pass-Seymore and still a far cry from the 100...
    Post by: wiigelec, Feb 3, 2011 in forum: New To The Hobby
  19. wiigelec
    Post

    ground probe

    Are you suggesting that one installed in a RESIDENCE would be something other than "residential grade"? So in your 25 years as an electrical...
    Post by: wiigelec, Feb 3, 2011 in forum: New To The Hobby
  20. wiigelec
    Post

    ground probe

    This is an extreme exageration, the spec on this recep which I recommend using is from 4-6 mA. http://tools.passandseymour.com/pdf/C02_C05.pdf It...
    Post by: wiigelec, Feb 3, 2011 in forum: New To The Hobby
Showing results 81 to 100 of 189 Next >
Search Again
Page 5 of 10