Apex Help

Discussion in 'General Reef Topics' started by ccscscpc, Apr 24, 2010.

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

  1. bwalker9801

    bwalker9801 Zoanthid

    Joined:
    Nov 10, 2008
    Messages:
    1,118
    Location:
    Saint Augustine, Florida
  2. Click Here!

  3. ccscscpc

    ccscscpc Millepora

    Joined:
    Feb 7, 2010
    Messages:
    943
    Location:
    CT
    Hey Zach....I have another issue and was wondering your thoughts on it....or anyone else who can help!!!

    I just installed my Apex last week and its working great except the outlets where I have my 4 pumps are off all the time.

    I dont have them plugged in there yet because I dont want them to turn off or be off.

    I have my lights, heaters, and fans all plugged in and working as they should be.

    Do you know how to correct this issue with the pumps not being on....is it the Fallback state or something?

    Thanks!

    Here is what my pump settings look like:
    Fallback (On/Off) On
    Initial off time (MMM:SS) 000.00
    On time (MMM:SS): 005.00
    Off time (MMM:SS) 005.00
    Feed timer (A-D) A
    Feed timer delay (MMM) 000
     
  4. ZachB

    ZachB Giant Squid

    Joined:
    Oct 12, 2008
    Messages:
    3,111
    Location:
    Earth
    Remove the other code -

    Fallback ON
    Set ON
     
    1 person likes this.
  5. ccscscpc

    ccscscpc Millepora

    Joined:
    Feb 7, 2010
    Messages:
    943
    Location:
    CT
    So go the Advanced portion and just put what you wrote in for each of my pumps?

    If I look at the Advanced section now it looks like this:
    Fallback ON
    OSC 000:00/005:00/005:00 Then ON
    If FeedA 000 Then OFF

    I should change it to this?:
    Fallback ON
    Set ON
     
  6. ZachB

    ZachB Giant Squid

    Joined:
    Oct 12, 2008
    Messages:
    3,111
    Location:
    Earth
    Yep. Too complicated. You can leave the Feed line in if you want it to turn off when you feed, otherwise, just set the status to always on and you're good to go.
     
  7. ccscscpc

    ccscscpc Millepora

    Joined:
    Feb 7, 2010
    Messages:
    943
    Location:
    CT
    When I made that change and look at it as a Pump again instead of Advanced it now looks like this(In Control Type)
    Fallback (On/Off) Off
    Initial off time (MMM:SS) 5:00
    On time (MMM:SS): 5:00
    Off time (MMM:SS) 5:00
    Feed timer (A-D) A
    Feed timer delay (MMM) 5

    Is that correct? And with them like this they will stay on all the time and come back when a power failure occurs right? Basically I want them on all the time and to come back after power fails just as if they were plugged into a surge strip or regular outlet.
    Thanks!
     
  8. Click Here!

  9. ZachB

    ZachB Giant Squid

    Joined:
    Oct 12, 2008
    Messages:
    3,111
    Location:
    Earth
    Don't change back to pump. You don't need to. Leave it on advanced, and just enter

    Fallback ON
    Set ON

    Then go to your status page and it should be set to Auto for that outlet. You will also notice that the outlet state is set to On. That will have it run 24/7 and turn back on after a power outage. Don't switch back to pump.
     
  10. ccscscpc

    ccscscpc Millepora

    Joined:
    Feb 7, 2010
    Messages:
    943
    Location:
    CT
    Ahhh....ok!

    Thanks again for your help!!! K+ again...(are you tired of the Karma yet?)
     
    1 person likes this.