bulkhead not holding its own

i installed a bulkhead on the bottom right side of my 40 g acrylic tank and although the bulkhead is on there tight, it is still dripping water every couple of seconds. is there any advice you have for me? i guess a valid question is which side does the o-ring go on (wet or dry), in my case looking at the picture.

 

The rubber gasket always goes on the flange Vs. the nut. You installed it backwards. You want the flange on the wet side with the gasket and the threads and the nut on the dry side.

 

is that why it is leaking? i knew it was backwards when i installed it i just didnt know it would matter

 

Yup.

 

It should still work provided you have the gasket against the flange.

If it's already there, put a towel underneath. When the salt creep dries, it will fix the leak. Just don't wipe off the dried salt.

 

is there any putty or glue or sealant that will let me get by? the cabinet isnt big enough for the 90º elbow and all the thread on the other side of the bulkhead

 

i installed mine the same way out of nasesity but i always put a real thin coat of patrolium jelly on the gasket just so it will slide wile tightning . maybee its the mechanic in me olways oiling filters so thay will come off lator and not leak

 

The gasket always goes on the wet side and, as inwall stated, it is typically best to put the threaded side on the dry side of the wall.

Did you put anything on the gasket to grease it? A little silicone o-ring grease will go a long way. If you don't use it then you need to really crank down the nut hard. Even if you do this, a small piece of rock or other debris can create a channel for the water.

 

i did use a oring and i didnt grease it but the oring is on the wet side. thanks for the silicone advice, ill try it

 

This is a Sticky Post I have done for several reef forums:
Bulkhead tips:

1. Always install bulkheads clean and dry, NO silicone, teflon or thread lubricants. Silicone and lubricants cause the gasket to scoot out or not seal properly. Have you ever removed an old automobile windshield or other gasketed glass? The rubber vulcanizes to the glass with time and creates a perfect seal without any help.

2. Before installing the bulkhead take a few minutes using a jewelers file, nail file or pocket knife and clean any excess flashing off both the male and female threads and from the flat gasket mating surfaces of the flange and nut. This is a common source of leaks.

3. Always install the gasket on the flange side of the bulkhead, never on the nut side, regardless if its inside (WET) or outside (DRY) the tank, it does not matter so laong as its against the flange. Installing the gasket next to the nut will lead to leaks as water travels along the threads around the gasket. Hand tighten only with maybe 1/4 to 1/2 turn additional, no more.

4. When using threaded bulkheads, again clean the excess flashing from the threads and valleys and use a small amount of teflon tape or better yet the stick or crayon type of thread lubricant designed specifically for PVC treads. These can be found at Lowes, HD, Ace and all hardware stores under names like Laco, Permatex and others.

I use this one and have since the 1980's with great success.
LA-CO: Product Detail - PLASTO-JOINT STIK® - Plastic Thread Sealant
It stays pliable forever and does not tear or roll out of the threads like teflon tape. My swimming pool plumbing up to 2" was all installed with this in 1983, outside in Phoenix AZ and its still pliable to this day!

5. Never support any pumps or piping from a bulkhead, always use supports so weight is not on a bulkhead and gasket causing differential stresses on the mating surfaces and leaks.

6. Never screw anything to the external threads of a bulkhead, these are not standard tapered pipe threads (NPT) and will leak. They are there to screw the nut on is all and are not normally even a standard diameter like 1" etc.

Exterior or external threads are only for the nut, as I pointed out. Some bulkheads are threaded on the inside with NPT or pipe threads and others are slip for friction fit or glued joints. I prefer interior threaded myself so they can be reused or disassembled if needed lie for a move.

Yes interior threads are standard pipe thread like PVC fittings. Exterior threads have no taper and can be odd sizes so PVC fittings will not thread on properly and will either wipe the threads out or leak or both.

Hope you get some use out of this.