phosphate reactor w/ phosguard

Discussion in 'Filters, Pumps, etc..' started by tonythereefer, Jan 15, 2013.

to remove this notice and enjoy 3reef content with less ads. 3reef membership is free.

  1. diverdan

    diverdan Bangghai Cardinal

    Joined:
    Sep 9, 2010
    Messages:
    1,389
    Location:
    San Diego
    You can use it loose in the reactor. I just started mine up yesterday with phosgaurd and so far my tank is a little cloudy and my leathers aren't as happy as they were prior to installation. I will be using it for another couple days and then I will switch to gfo.
     
  2. Click Here!

  3. tonythereefer

    tonythereefer Fire Shrimp

    Joined:
    Dec 27, 2012
    Messages:
    322
    Location:
    Auburn, MA.
    Did you rinse the phosguard? I started using mine on Friday and rinsed it through the reactor into a bucket until the water came out clear and all my corals seem happy and I'm seeing a decent reduction in cyano
     
  4. diverdan

    diverdan Bangghai Cardinal

    Joined:
    Sep 9, 2010
    Messages:
    1,389
    Location:
    San Diego
    Yes I did, I had help on my thread and the diagnosis was that I had too much flow through the reactor. The cloudiness has already cleared up and is looking better. How long are you planning on leaving the phosgaurd in the reactor befor you replace with more or gfo?
     
  5. tonythereefer

    tonythereefer Fire Shrimp

    Joined:
    Dec 27, 2012
    Messages:
    322
    Location:
    Auburn, MA.
    I don't think I'll be switching to gfo my plan is to use the phosguard until my phosphates aee around 0.03 and 0.00 then I'll take the reactor out of service and test weekly, once I see my phosphates start to creep up I will put thecreactor back into service.

    Sounds good on paper lol but I'll see how that works out
     
  6. diverdan

    diverdan Bangghai Cardinal

    Joined:
    Sep 9, 2010
    Messages:
    1,389
    Location:
    San Diego
    That sounds like a good plan. Paper plans are always sound good. Thanks for your help.
     
  7. tonythereefer

    tonythereefer Fire Shrimp

    Joined:
    Dec 27, 2012
    Messages:
    322
    Location:
    Auburn, MA.
    I may also cut the amount of phosguard and just keep the reactor running full time
     
  8. Click Here!

  9. diverdan

    diverdan Bangghai Cardinal

    Joined:
    Sep 9, 2010
    Messages:
    1,389
    Location:
    San Diego
    I was thinking about cutting down the phosguard when I see the desired results. I am showing 0 phosphate with my test kit but I have cyano on the substrate and on some rock that I just can not get rid of. Weekly water changes, more flow, you name it I've tried it. So I built my reactor and now trying the phosguard. It is something I haven't tried so its worth a shot.
     
  10. tonythereefer

    tonythereefer Fire Shrimp

    Joined:
    Dec 27, 2012
    Messages:
    322
    Location:
    Auburn, MA.
    The cyano you're going to want to remove manually, with the low phosphates it will die but still remain on the surface just brown and disgusting, the actual left over red stuff will come back but will be less, keep removing it as you see it and eventually it will be gone. Every other day I was vacuuming off my rocks of the stuff, it was only last week that I noticed it wasn't growing back

    Stick with it, be diligent and eventually you will beat it :)